I’m guessing the bump to 6GHz means range is even lower. Seems we’re leaning towards a future of hardwired-equivalent speed and reliability… within 1 meter.
I know this is a joke but please do not buy repeaters they do not work how you would expect them to work.
Repeaters take an already weak signal and amplify that signal while increasing the latency. Sure this makes the signal go farther but it doesn’t increase the bandwidth and if you stand in between the originating wifi source and the repeater your device may not migrate to the source wifi even though it might be faster because the reapeter has the illusion of being a better signal because it’s louder.
The better route to go is to use multiple wifi APs through out the building connected back to your router with ethernet.
You could also go with mesh access points but you have to do a lot of research and planning; The two key things to look out for is they mesh system must have a dedicated backhaul and you must place them where each node has an excellent signal to the next node. Since most backhauls run on 5Ghz and 6Ghz this means there shouldn’t be any walls between them.
Exactly. I’m going to be running Ethernet through my house soon, and even if we stay full Wi-Fi, we’ll benefit by having physical cables connecting the APs. I already have a separate AP, just need to run the cables to get a second in our basement where the signal is weak.
Is fiber really worth the extra complexity and expense? It’s strength is in longer distances with mostly straight runs. When you are doing short distances with multiple turns, copper is much easier and more forgiving. Splicing fiber is difficult if something breaks during or after installation, on top of the expense and skill needed for proper termination. Tools and hardware for copper are cheap, easy to use, and ubiquitous.
Yes but WiFi 7 FINALLY lets devices connect to multiple BANDS at the same time with a new feature called Multi-link operation (MLO)… IE the device can hold on to a longer range but slower band and more seamlessly transmit data over the best one at the time.
I think the prevalence of mesh systems is intended to remedy this. Instead of a single AP that can cover your entire house you can mesh two or three (or more) APs to get the coverage desired.
That’s how I do it, except because I have all these AP’s I just set them up near the devices that will use it and plug them all into the AP’s and use the backhaul which is way more reliable. Phones and tablets are the only things that use the wifi and never really found an issue with speed or reliability since moving to mesh.
That’s an advantage if you utilize it right. Less range means your neighbor’s wifi is less likely to interfere with your own. Multiple access points are a superior way to get coverage of your whole house than some octopus antenna monstrosity.
The inverse square law doesn’t have to be a problem.
I’m guessing the bump to 6GHz means range is even lower. Seems we’re leaning towards a future of hardwired-equivalent speed and reliability… within 1 meter.
Then you can buy a bunch of repeaters and the economy is saved
I know this is a joke but please do not buy repeaters they do not work how you would expect them to work.
Repeaters take an already weak signal and amplify that signal while increasing the latency. Sure this makes the signal go farther but it doesn’t increase the bandwidth and if you stand in between the originating wifi source and the repeater your device may not migrate to the source wifi even though it might be faster because the reapeter has the illusion of being a better signal because it’s louder.
The better route to go is to use multiple wifi APs through out the building connected back to your router with ethernet.
You could also go with mesh access points but you have to do a lot of research and planning; The two key things to look out for is they mesh system must have a dedicated backhaul and you must place them where each node has an excellent signal to the next node. Since most backhauls run on 5Ghz and 6Ghz this means there shouldn’t be any walls between them.
Exactly. I’m going to be running Ethernet through my house soon, and even if we stay full Wi-Fi, we’ll benefit by having physical cables connecting the APs. I already have a separate AP, just need to run the cables to get a second in our basement where the signal is weak.
Do yourself a favor and drop fiber at the same time. That’s my plan for whenever I get around to crawling in the attic.
Is fiber really worth the extra complexity and expense? It’s strength is in longer distances with mostly straight runs. When you are doing short distances with multiple turns, copper is much easier and more forgiving. Splicing fiber is difficult if something breaks during or after installation, on top of the expense and skill needed for proper termination. Tools and hardware for copper are cheap, easy to use, and ubiquitous.
Yes but WiFi 7 FINALLY lets devices connect to multiple BANDS at the same time with a new feature called Multi-link operation (MLO)… IE the device can hold on to a longer range but slower band and more seamlessly transmit data over the best one at the time.
I think the prevalence of mesh systems is intended to remedy this. Instead of a single AP that can cover your entire house you can mesh two or three (or more) APs to get the coverage desired.
That’s how I do it, except because I have all these AP’s I just set them up near the devices that will use it and plug them all into the AP’s and use the backhaul which is way more reliable. Phones and tablets are the only things that use the wifi and never really found an issue with speed or reliability since moving to mesh.
That’s an advantage if you utilize it right. Less range means your neighbor’s wifi is less likely to interfere with your own. Multiple access points are a superior way to get coverage of your whole house than some octopus antenna monstrosity.
The inverse square law doesn’t have to be a problem.