Hi everyone,

I just got an Elegoo Saturn 2 and did one successful print and tried another but ran into some issues after it printed.

I’m using a water washable resin for both prints. Also using the Elegoo Mercury wash and cure machine for this.

Once the print finished, I put it into the wash with water and let it spin for 3 minutes. I took out the print and let it dry off on a metal plate. Then I moved it back to the Mercury to cure under the UV lights. Once it seemed cured, I began removing the supports.

This is a fairly big, heavy object that was being printed. This is the object here https://www.thingiverse.com/thing:2482299

I titled it on its side in the slicer so that the full object could fit on the bed and used the default settings with medium supports.

One issue is that the color turned a cloudish color. To my understanding, this is because I didn’t let it dry enough after the wash before curing. Is that correct or is there another reason for that?

The second issue I had is that there was a few layer shifts in the print. Here’s a picture of the layer shifts https://i.imgur.com/eV5XSxN.jpg https://i.imgur.com/TKAFD1x.jpg I did once knock the printer which I know can cause layer shifts. But I’m seeing more than one layer shift which leads me to believe something else happened. What else could cause layer shifts besides the printer being physically knocked?

The third issue is that the very first layers of the print are coming off. Here’s some pictures of this https://i.imgur.com/CrFdExh.jpg https://i.imgur.com/fKpff9G.jpg my thinking is that maybe this is because I didn’t choose heavy supports since this was a larger object? Could that do it? But what would cause this part to be flat too? It’s supposed to be rounded, but after pulling the supports, this area is flat despite it being elevated from the bed to be held by supports.

  • Okalaydokalay@lemm.eeOP
    link
    fedilink
    English
    arrow-up
    2
    ·
    1 year ago

    Thanks for the recommendations!

    A new USB is definitely on my list of things to get…I honestly forgot about that recommendation how it can cause weird issues, but that’s a good point to rule out.

    I tried adding some new supports on another attempt last night but had some issues with the print seemingly not printing at all, or maybe it was and I was impatient. Going to try again tonight after watching this video, thank you for the tips!

    • CaptainFlintlockFinn@lemmy.ca
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      Any time!

      If it didn’t print at all I’d be looking at that USB right away. I had many half printed things and corrupted files before I clued in.

      • Okalaydokalay@lemm.eeOP
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        I’m unsure as it said it was 73% done but I saw supports and not enough actually printing under the supports…it was weird. But when I went to clean everything, there was a huge circular piece of plastic in the bottom of the vat. So I’m so confused lol

        But you’re right! I’m starting from scratch today with deep cleaning on everything and recalibrating. A new USB would be perfect to match!

        • CaptainFlintlockFinn@lemmy.ca
          link
          fedilink
          English
          arrow-up
          2
          ·
          edit-2
          1 year ago

          Good call on a deep clean. I’m sure you’ll figure it out. I think it’s a lot of trial and error for most people at the beginning.

          That piece on the FEP sheet is where it let go from the supports when the build plate lifted. More support will probably fix that.

          I always think about what’s happening when I’m doing supports. The resin gets cured on the FEP then the build plate moves up and pulls that layer off the FEP. The part is being pulled by forces in opposite directions so we need to make sure that the part hanging on to the build plate is sufficiently anchored so it’ll pop off the FEP and not off the build plate.

          • ekky43@lemmy.dbzer0.com
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            @Okalaydokalay@lemm.ee

            True, the sticking can be quite the hassle. I personally (carefully) sanded down the metal print plate, as to make it more rough and therefore more sticky, and then bought some new film from fepshop.com which should be less sticky than the original on my Elegoo Mars Pro 1.

            That worked really well, minimizing layer shifts quite a bit and allowing me to use less supports without the print going haywire.